home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
Night Owl 6
/
Night Owl's Shareware - PDSI-006 - Night Owl Corp (1990).iso
/
001a
/
cspsetup.zip
/
SPITFIRE.TXT
< prev
next >
Wrap
Text File
|
1991-04-29
|
4KB
|
91 lines
Using the Compucom Speedmodem with SPITFIRE 3.0 BBS Software:
This is by no means a technical document on all the different ways to
initialize your CompuCom Speedmodem for SPITFIRE, but a SIMPLE guide.
oo ..Be sure the Speedmodem ROM version is at least 2.51. Type ATI3...
\/ ..from any communications program in TERMINAL mode for results...
..EXAMPLE: (c) Copyright CompuCom 1990 V2.51
oo ..Refer to the init string below...
\/
SPITFIRE /I19200 /C2 /M AT&F2 +F *H2%C0 S0=0S2=1&C1&D2V1Q0M0H0X1&W
| | | |___| | |____| |________________________|
| | | | F | |
| | | | A | Recommended for Spitfire!
| | | | X |
| | | | | Depends on error mode wanted
| | | | O *H1 or *H2 (MNP-5)
| | | | F *H1 or *H2%C0 (MNP-4) -|Recommend
| | | | F *H1 or *H2\N0 (no MNP)-|either one
| | | | |
| | | | For COMBO only, do NOT use on CHAMP.
| | | | NOT USED FOR Roms after 4/1/91
| | | A must for Speedmodem!
| | |
| | OVERRIDES Spitfire init string...
| |
| Selects com port...
|
Locks the port...
oo ..Place it in the file SF.BAT that starts Spitfire...
\/
..(I.E.)
:LOOP
C:\
CD\SF
SPITFIRE /I19200 /C2 /M AT&F2+F*H2%C0S0=0S2=1&C1&D2V1Q0M0H0X1&W
^^Not for roms after 4/1/91
oo ..It is a good idea to change the actual string within Spitfire...
\/
╒═[ SPITFIRE NODE 1 MODEM CONFIGURATION ]═════════════════════════════╕
│ │
│ <S> Serial Port No................. : 2 │
│ <B> System Baud Rate............... : 19200 │
│ <I> Initialization String.......... : │
│ AT&F2*H2%C0S0=0S2=1&C1&D2V1Q0M0X1H0&W │
│ <M> Modem - Error Correction Type.. : Yes │
│ <E> Error Correction Message....... : REL │
│ <H> Hardware Data Flow Control..... : Yes │
│ <A> Answer On What Ring............ : 1 │
│ <D> Display Result Messages........ : On │
│ <C> Disconnect Delay............... : 3 │
│ <U> Use High Speed Async Routines.. : Yes/No oo ..Either way works..│
│ <R> Baud Rate Requirement.......... : 0 \/ │
│ │
│ Enter Command or <Q>uit - │
│ │
╘═════════════════════════════════════════════════════════════════════╛
oo ..*H2%C0 can be substituted with other variations...
\/ ..as recommended in the Speedmodem manual...
oo ..If using the COMBO, add +F to the Initialization string...
\/ ..turns fax off on the COMBO, returns ERROR on the CHAMP...
NOTE: +F NOT USED for roms after 4/1/91
Dialing out:
oo ..RTS-CTS ON, ALL BAUD at 19200, AUTO BAUD DETECT OFF...
\/
..When using a long distance carrier with the Speedmodem...
..call your LD customer service and ask if a "carrier code"...
..is needed for proper "bandwidth" on "asynchronous" connections...
oo ..An example where this code is needed is the US Sprint...
\/ ..FIBER OPTIC NETWORK, to access a ""full-bandwidth" line...
..the code 10333 is needed, that is dial 10333-1-800-000-0000...
..this ensures that the FULL bandwidth is available to you...
..otherwise, a sudden "No carrier" can result...
This by no means covers all the ways to use SPITFIRE with a Compucom
Speedmodem. But it should help you initially (pun?). If all else
fails, don't forget to read the doc's!
<End of File>